Single-phase, 24 V DC (for SIMATIC ET 200SP)

訂貨數據

概述

In terms of design and functionality, the SIMATIC ET 200SP PS single-phase load power supply with automatic range switching of the input voltage is perfectly matched to the SIMATIC ET 200SP. The SIMATIC component and the power supply are wired by means of uniform push-in terminal technology. The 24 V supply provides power to the ET 200SP system components such as the interface module, technology module and communication module, as well as the digital or analog inputs/outputs. Comprehensive certifications, such as UL or GL, facilitate universal use. Its extremely flat design also makes this power supply ideally suited for installation in compact on-site control boxes.

設計

Mounting of the ET 200SP power supply on DIN rail to the left of the SIMATIC ET 200SP component
Direct mounting side-by-side is possible for the modules;
Exception: SIMATIC ET 200SP component has PROFINET connector mounted on the left → 5 mm spacer required
Three separate load circuit connectors for easy commissioning and maintenance
Diagnostic LED for indicating "Output voltage 24 V DC O.K."
On/off switch for isolated replacement of SIMATIC ET 200SP modules

功能

Connection to all single-phase 50/60 Hz networks (85 V... 132 V/170 V... 264 V) through automatic range switching
Adjustable output voltage for compensating voltage drops
Short-term mains buffering
Signal contact for further processing of "Output voltage 24 V DC O.K." in the controller
Current monitor for further processing of the present energy consumption in the controller
Output voltage 24 V DC, stabilized, short circuit-proof, open circuit-proof
Parallel connection of two power supplies for enhanced performance
High degree of efficiency up to 90%
Temperature range -30 °C…+60°C/70 °C with derating
Easy connection of loads with high power requirements through excellent overload behavior

技術規范

Article number	6EP7133-6AB00-0BN0	6EP7133-6AE00-0BN0
Product	SIMATIC ET 200SP PS	SIMATIC ET 200SP PS
Power supply, type	24 V/5 A	24 V/10 A
Input
Input	1-phase AC	1-phase AC
Supply voltage
● 1 at AC Rated value	120 V	120 V
● 2 at AC Rated value	230 V	230 V
● Note	Automatic range selection	Automatic range selection
Input voltage
● 1 at AC	85 ... 132 V	85 ... 132 V
● 2 at AC	170 ... 264 V	170 ... 264 V
Wide-range input	No	No
Overvoltage resistance	2.3 × Vin rated, 1.3 ms	2.3 × Vin rated, 1.3 ms
Mains buffering at Iout rated, min.	20 ms; at Vin = 93/187 V	20 ms; at Vin = 93/187 V
Rated line frequency 1	50 Hz	50 Hz
Rated line frequency 2	60 Hz	60 Hz
Rated line range	47 ... 63 Hz	47 ... 63 Hz
Input current
● at rated input voltage 120 V	2.16 A	4.34 A
● at rated input voltage 230 V	1.22 A	1.92 A
Switch-on current limiting (+25 °C), max.	45 A	60 A
I2t, max.	3.15 A2·s	6.3 A2·s
Built-in incoming fuse	T 3,15 A/250 V (not accessible)	T 6.3 A/250 V (not accessible)
Protection in the mains power input (IEC 898)	recommended LS switch: B/C 6 A/3 A	recommended LS switch: B/C 10 A/6 A
Output
Output	Controlled, isolated DC voltage	Controlled, isolated DC voltage
Rated voltage Vout DC	24 V	24 V
Total tolerance, static ±	3 %	3 %
Static mains compensation, approx.	0.1 %	0.1 %
Static load balancing, approx.	1 %	1 %
Residual ripple peak-peak, max.	150 mV	150 mV
Residual ripple peak-peak, typ.	50 mV	50 mV
Spikes peak-peak, max. (bandwidth: 20 MHz)	240 mV	240 mV
Spikes peak-peak, typ. (bandwidth: 20 MHz)	150 mV	150 mV
Adjustment range	22.8 ... 28 V	22.8 ... 28 V
Product function Output voltage adjustable	Yes	Yes
Output voltage setting	via potentiometer	via potentiometer
Status display	Green LED for 24 V OK	Green LED for 24 V OK
Signaling	Relay contact (NO contact, rating 60 V DC/ 0.3 A) for "24 V OK"	Relay contact (NO contact, rating 60 V DC/ 0.3 A) for "24 V OK"
On/off behavior	Overshoot of Vout < 3 %	Overshoot of Vout < 3 %
Startup delay, max.	0.3 s	0.3 s
Voltage rise, typ.	30 ms	30 ms
Rated current value Iout rated	5 A	10 A
Current range	0 ... 6 A	0 ... 12 A
● Note		10 A up to +60°C; +60 ... +70 °C: Derating 3%/K
Supplied active power typical	120 W	240 W
Short-term overload current
● on short-circuiting during the start-up typical	15 A	30 A
● at short-circuit during operation typical	15 A	30 A
Duration of overloading capability for excess current
● on short-circuiting during the start-up	800 ms	750 ms
● at short-circuit during operation	800 ms	800 ms
Parallel switching for enhanced performance	Yes	Yes
Numbers of parallel switchable units for enhanced performance	2	2
Efficiency
Efficiency at Vout rated, Iout rated, approx.	88 %	90 %
Power loss at Vout rated, Iout rated, approx.	17 W	26 W
Power loss [W] during no-load operation maximum	2.7 W	2.8 W
Closed-loop control
Dynamic mains compensation (Vin rated ±15 %), max.	0.3 %	0.3 %
Dynamic load smoothing (Iout: 10/90/10 %), Uout ± typ.	3 %	3 %
Load step setting time 10 to 90%, typ.	1 ms	1 ms
Load step setting time 90 to 10%, typ.	1 ms	1 ms
Protection and monitoring
Output overvoltage protection	protection against overvoltage in case of internal fault Vout < 31.8 V	protection against overvoltage in case of internal fault Vout < 31.8 V
Current limitation	7 ... 7.5 A	14 ... 15 A
Property of the output Short-circuit proof	Yes	Yes
Short-circuit protection	Constant current characteristic	Constant current characteristic
Enduring short circuit current RMS value
● typical	7 A	14.1 A
Overcurrent overload capability in normal operation	overload capability 150 % Iout rated up to 5 s/min	overload capability 150 % Iout rated up to 5 s/min
Overload/short-circuit indicator	-	-
Safety
Primary/secondary isolation	Yes	Yes
Galvanic isolation	Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178	Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178
Protection class	Class I	Class I
Leakage current
● maximum	3.5 mA	3.5 mA
● typical	1 mA	1 mA
CE mark	Yes	Yes
UL/cUL (CSA) approval	cULus-Listed (UL61010-2-201, CSA C22.2 No.142), cCSAus (CSA C22.2 No. 60950-1, UL 60950-1)	cULus-Listed (UL61010-2-201, CSA C22.2 No.142), cCSAus (CSA C22.2 No. 60950-1, UL 60950-1)
CB approval	Yes	Yes
Marine approval	BV, DNV GL	BV, DNV GL
Degree of protection (EN 60529)	IP20	IP20
EMC
Emitted interference	EN 61000-6-3 Class B	EN 61000-6-3 Class B
Supply harmonics limitation	EN 61000-3-2	EN 61000-3-2
Noise immunity	EN 61000-6-2	EN 61000-6-2
Operating data
Ambient temperature
● during operation	-30 ... +70 °C	-30 ... +70 °C
— Note	with natural convection	with natural convection
● during transport	-40 ... +85 °C	-40 ... +85 °C
● during storage	-40 ... +85 °C	-40 ... +85 °C
Humidity class according to EN 60721	Climate class 3K3, no condensation	Climate class 3K3, no condensation
Mechanics
Connection technology	Push-in terminals	Push-in terminals
Connections
● Supply input	L, N, PE: 1 push-in terminal each for 0.2 ... 2.5 mm2 single-core/finely stranded	L, N, PE: 1 push-in terminal each for 0.2 ... 2.5 mm2 single-core/finely stranded
● Output	+, -: 2 push-in terminals each for 0.2 ... 2.5 mm2	+, -: 2 push-in terminals each for 0.2 ... 2.5 mm2
● Auxiliary	Signaling contact: 2 push-in terminals for 0.2 ... 2.5 mm2	Signaling contact: 2 push-in terminals for 0.2 ... 2.5 mm2
Connections signaling contact	2 push-in terminals for 0.2 ... 2.5 mm2	2 push-in terminals for 0.2 ... 2.5 mm2
Product function
● removable terminal at input	Yes	Yes
● removable terminal at output	Yes	Yes
Width of the enclosure	160 mm	160 mm
Height of the enclosure	117 mm	117 mm
Depth of the enclosure	74 mm	74 mm
Required spacing
● top	50 mm	50 mm
● bottom	50 mm	50 mm
● left	0 mm	0 mm
● right	0 mm	0 mm
Weight, approx.	0.5 kg	0.7 kg
Product feature of the enclosure housing for side-by-side mounting	Yes	Yes
Installation	Snaps onto DIN rail EN 60715 35x7.5/15	Snaps onto DIN rail EN 60715 35x7.5/15
Electrical accessories	Redundancy module, buffer module, selectivity module, DC UPS	Redundancy module, buffer module, selectivity module, DC UPS
MTBF at 40 °C	1 598 441 h	1 114 510 h
Other information	Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)	Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)

來源：上海勵輝自動化科技有限公司

免責聲明：焊材網轉載作品均注明出處，本網未注明出處和轉載的，是出于傳遞更多信息之目的，并不意味著贊同其觀點或證實其內容的真實性。如轉載作品侵犯作者署名權，或有其他諸如版權、肖像權、知識產權等方面的傷害，并非本網故意為之，在接到相關權利人通知后將立即加以更正。聯系電話：0571－87774297。