西門子工業以太網線Profinet總線電纜4芯

西門子代理商大量庫存 現貨 

西門子代理商現貨供應 

原裝正品  質保一年

上海斌勤電氣技術有限公司

發布人：康奎 （銷售經理）發布

本公司簽約正式的銷售合同，并開具13%的增-值-稅-發-票。

外地客戶統一采用快遞發貨,也支持上門提貨，貨物快遞到您手時候,一定要開箱檢驗!如有損壞,請拒絕簽收,并由快遞公司返回!

在你簽收后表示你對該貨物沒有異議!我們會給予您檢測時間,并請在貨物到給予確認,謝謝合作!

產品均為密封包裝，外包裝詳見產品圖片，白色標簽上均有產品訂貨號和產地，各位買家在收到貨后，請核對型號，無誤后再拆包裝、

本公司宗旨：本著以誠信為本，以顧客為中心.質量保證·服務誠信·價格實惠.

為用戶提供專業的自動化產品及服務！

相關西門子產品技術：

SIMATIC NET PROFIBUS CP 5711 Released for Delivery

Entry

Associated product(s)

The CP 5711 communication processor is herewith release for delivery. Please note: The following approval has not yet been obtained: cULus - The approval and the certif ...

The CP 5711 communication processor is herewith release for delivery.

Please note:

The following approval has not yet been obtained:

cULus - The approval and the certificate are expected by mid. May 2009.

1. Product description

The CP 5711 is an innovation of the existing SIMATIC NET CP 5512 for PGs/PCs with USB V2.0 ports. With its USB V2.0 connection, the CP 5711 can be used on many different computer platforms.     

Innovation of the PG/PC connector technology for USB V2.0:

The CP 5711 is connected via a USB V2.0 port, allowing flexible use of the module. USB V2.0 is available on many computer platforms and applications for the CP 5711 are therefore manifold. The CP 5711 can also be used on a USB V1.1 port, but the performance will be lower in this case.

Functionally compatible with the CP 5512, as well as PC Adapter USB

Applications created for the CP 5512 can be used for the CP 5711 without any changes to the configuration or the user software.

The CP 5711 is functionally compatible with the PC Adapter USB for engineering applications (e.g. STEP7)

+ 5 V Power supply from USB V2.0

The communication processor is supplied with power from the USB port of the PC system.  

+24 V optional external power supply

The external 24 V power supply covers two application areas:

        - The power supply from the USB V2.0 port is not sufficient (power supply of the PC is too weak; USB ports are not designed for 500 mA USB standard)

        - PROFIBUS Termination is assured even when the USB cable is disconnected (active supply of the PROFIBUS connection termination)

SIMATIC S7 or SITOP power supplies can be used to provide the external voltage supply.

Mechanical USB latching

Additional mechanical latching of the included USB connecting cable on the housing of the CP 5711. This safeguards the USB connection in the case of mobile use and also for applications in switchboards.

Diagnostic information via LEDs

Five LEDs are available on the CP 5711 communication processor to provide extensive diagnostics (power USB, power external, identify, Link/SF and Activity.

    - Power USB = module is supplied with 5 V from the USB port

    - Power Ext = module is supplied with 24 V from an external source

    - Identify = USB identification phase - startup phase of the module

    - Link/System Fault = two-colored LED (green/red) providing the user with status information:

                        - the LED lights up green when subscribers are identified on the connected PROFIBUS network (Link Status).

                        - the LED lights up red if an error occurs on the CP 5711.

- Activity = the module has synchronized itself on the PROFIBUS network and the PROFIBUS token is available on the PROFIBUS network.  

Mounting on a mounting rail (with optional accessories)

A separate mounting bracket is available for use of the CP 5711 in switchboards and mounting on 35 mm standard rails.

The existing CP 5512 module with Cardbus technology will continue to be sold in parallel with the CP 5711. Our customers thus have flexibility and can decide freely whether they wish to use a vacant Cardbus slot, or a USB port to operate the relevant SIMATIC NET communication processor. An additional area of application are PC-based systems with no separate card slot and only USB ports.

2. Ordering data

Product Name Order No. Remark

CP 5711 6GK1571-1AA00 CP 5711 Hardware, operating instructions, USB cable

CP 5711 + MPI cable 6GK1571-1AM00 CP 5711 Hardware, operating instructions, USB cable, 5 m MPI cable

Mounting rail bracket for CP 5711 6GK1571-1AA00-0AH0  

3. Target applications

Target applications for the SIMATIC NET CP 5711 are service and engineering (e.g. with STEP 7 for plant commissioning). Other options include customer applications (e.g. HMI, SCADA, PC-based controllers, etc.) on PC systems with a USB port.

Application area:

- STEP 7 with V5.4 SP 5

- WinCC

- WinCC Flexible 

- Micro/WIN

- SOFTNET-DP with Version 7.1 + SP1

- SOFTNET-S7 with Version 7.1 + SP1

- SOFTNET DP Slave with Version 7.1 + SP1